CWNP Certified Wireless Analysis Professional CWAP-404 Exam Dumps: Updated Questions & Answers (July 2025)

A STA that supports 802.11k Radio Measurement would send a Neighbor Request to an AP to request a list of neighboring APs which the STA can use as roaming candidates. A Neighbor Request is an Action frame that contains a subelement specifying the type of information that the STA wants to receive from the AP. A Neighbor Report is an Action frame that contains a subelement with a list of neighboring APs that match the criteria specified in the Neighbor Request. The Neighbor Report provides information such as BSSID, channel, operating class, and PHY type of each neighboring AP. This information helps the STA to perform intelligent roaming decisions based on signal quality, load, and compatibility . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 434; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 435.

The CRC is calculated over the MAC Header and Frame Body only. The CRC (Cyclic Redundancy Check) is a 32-bit value that is used for error detection in wireless transmissions. The CRC is calculated over the MAC Header and Frame Body of a PSDU, which are the parts of the data unit that contain information such as source and destination addresses, frame type, frame control, sequence number, payload, etc. The CRC is appended to the end of the PSDU as a FCS (Frame Check Sequence) field. The CRC is not calculated over the PHY Header or PHY Preamble, which are parts of the PPDU that contain information such as modulation, coding, data rate, etc. The PHY Header and PHY Preamble are added or removed by the PHY layer during the conversion between PSDU and PPDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98

Every Beacon frame must contain a DTIM is not a true statement concerning DTIMs. DTIM stands for Delivery Traffic Indication Message, and it is a subfield within the TIM (Traffic Indication Map) element in a Beacon frame. The DTIM indicates how many Beacon frames (including the current one) will appear before the next DTIM. For example, if the DTIM interval is set to 3, it means that every third Beacon frame will contain a DTIM. Buffered broadcast and multicast traffic will be transmitted following a DTIM, so that STAs in power save mode can wake up and receive them. The DTIM interval can also dictate when an STA will wake up to listen to Beacon frames, as some STAs may choose to only listen to Beacon frames that contain a DTIM . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 200; CWAP-404 CertifiedWireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 201.

The default 802.11 authentication method for a STA when using Pre-RSNA is Open System. This is the simplest and most common authentication method, which does not provide any security or encryption. In Open System authentication, the STA sends an Authentication Request frame to the AP, and the AP responds with an Authentication Response frame with a status code of success. After this, the STA can proceed to association with the AP . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 181; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 183.

If the SSID element has a length of 0 in a Beacon frame decode, it means that the beacon is from a BSS configured to hide the SSID. The SSID element is a part of the Beacon frame that contains the name or identifier of the BSS. The SSID element has two fields: length and value. The length field indicates how many bytes are used for the value field, which contains the actual SSID string. If the length field is 0, it means that there is no value field or SSID string in the element. This is a common technique used by some APs to hide their SSID from passive scanning clients or potential attackers. However, this technique does not provide much security, as there are other ways to discover or reveal the hidden SSID, such as active scanning or capturing probe response or association frames. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 122-123

The most likely issue that can be identified from the spectrum analysis is a power mismatch between the APs and the clients. A power mismatch occurs when the APs transmit at a higher power level than the clients, or vice versa. This can cause asymmetric communication, where one side can hear the other, but not vice versa. This can result in poor performance, disconnections, or packet loss. A spectrum analysis can reveal a power mismatch by showing different signal amplitudes or RSSI values for the APs and the clients on the same channel or frequency. The other options are not correct, as they cannot be identified from the spectrum analysis alone. The tablets’ SSID, power save mode, and noise floor can be determined by using other tools or methods, such as protocol analysis, site survey, or device configuration. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 3: Spectrum Analysis, page 79-80

RTS is not a valid acknowledgement frame. RTS stands for Request To Send, and it is a control frame that is used to initiate an RTS/CTS exchange before sending a data frame. The purpose of an RTS/CTS exchange is to reserve the medium for a data transmission and avoid collisions with hidden nodes. An acknowledgement frame is a control frame that is used to confirm the successful reception of a data frame or a block of data frames. The valid acknowledgement frames are CTS (Clear To Send), Ack (Acknowledgement), and Block Ack (Block Acknowledgement) . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 186; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 187; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 189; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 190.

Before a retransmission, the CWmax (Contention Window maximum) value doubles and increases by 1. The CWmax is a parameter that determines the upper limit of the random backoff time that a STA (station) has to wait before attempting to access the medium. The random backoff time is chosen from a range of values between CWmin (Contention Window minimum) and CWmax. The CWmin and CWmax values depend on the AC (Access Category) of the traffic and the PHY type of the STA. If a transmission fails due to a collision or an error, the STA has to retransmit the frame after waiting for another random backoff time. However, to reduce the probability of another collision, the STA increases its CWmax value by doubling it and adding 1. This increases the range of possible backoff values and spreads out the STAs more evenly. The STA resets its CWmax value to its original value after a successful transmission or after reaching a predefined limit. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 7: QoS Analysis, page 196-197

The device finder is a common feature of a spectrum analyzer that helps locate a non-802.11 interference source. The device finder uses a directional antenna to measure the signal strength of a specific frequency or signal source. By pointing the antenna in different directions, the device finder can indicate the direction and distance of the interference source. The device finder can also filter out other signals that are not related to the interference source. The other options are not correct, as they do not help locate a non-802.11 interference source. Max hold and min hold are features that show the maximum and minimum RF power levels over time,respectively. Location filter is a feature that filters out signals that are not from a specific location or area. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 3: Spectrum Analysis, page 77-78

The function of the PHY layer is to convert PSDUs to PPDUs for transmissions and PPDUs to PSDUs for receptions. A PSDU (PHY Service Data Unit) is the data unit that is passed from the MAC layer to the PHY layer for transmission, or from the PHY layer to the MAC layer for reception. A PPDU (PHY Protocol Data Unit) is the data unit that is transmitted or received over the wireless medium by the PHY layer. A PPDU consists of a PSDU and a PHY header, which contains information such as modulation, coding, and data rate. The PHY layer adds or removes the PHY header to or from the PSDU during the conversion process. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98