Checkpoint Check Point Certified Maestro Expert (CCME) R81.X 156-836 Exam Dumps: Updated Questions & Answers (July 2025)

The asg calc command is a tool to show which SGM is selected to receive traffic based on the distribution mode and the packet parameters. It takes the port number, the source IP, the destination IP, and optionally the source port and the destination port as arguments and returns the SGM ID and the hash value. For example, asg calc 1 10.0.0.1 20.0.0.2 1234 80 will show which SGM will receive the traffic from 10.0.0.1:1234 to 20.0.0.2:80 on port 1.

References

•Check Point Certified Maestro Expert (CCME) R81.X Courseware, Module 4: Using the Command Line Interface and WebUI, Lesson 4.1: asg calc, page 4-5

•Check Point R81 Maestro Administration Guide, Chapter 4: Using the Command Line Interface and WebUI, Section: asg calc, page 4-5

•asg calc - Check Point Software

The cpinfo command is a tool that collects diagnostic information about the orchestrator, such as hardware, software, network, configuration, and logs. The cpinfo command generates a file that can be sent to Check Point Support for analysis and troubleshooting. The cpinfo command can be run on the orchestrator’s CLI or WebUI.

References =

•Check Point Maestro R81.X Administration Guide, page 68, section “cpinfo” 1

•Check Point Maestro R81.X Getting Started Guide, page 30, section “cpinfo” 2

•Maestro Hyperscale Orchestrator Datasheet - Check Point Software 3

1: https://www.manualslib.com/manual/2031661/Check-Point-Maestro-R80-20sp.html 2: https://sc1.checkpoint.com/documents/R81/WebAdminGuides/EN/CP_R81_Maestro_GettingStarted/html_frameset.htm 3: https://www.checkpoint.com/downloads/products/maestro-hyperscale-orchestrator-datasheet.pdf

References

•R81.20 Maestro Cheat Sheet version 7 - Check Point CheckMates, page 2

•[Maestro Expert (CCME) Course - Check Point Software], page 31

•[Check Point Certified Maestro Expert (CCME) R81.X - Global Knowledge], page 3

The asg perf -v command is used to find bottlenecks in the system that are affecting performance, even functionality in some cases. The asg perf -v command displays the performance statistics of the Security Group Modules (SGMs) in the Security Group, such as throughput, packet rate, CPU utilization, memory usage, and more. The asg perf -v command also shows the distribution mode and the correction rate of each SGM, which can indicate potential issues with asymmetric routing or load balancing. The asg perf -v command can help identify which SGMs are overloaded, underutilized, or misconfigured, and provide insights for troubleshooting and optimization.

References =

•Check Point Maestro R81.X Administration Guide, page 67, section “asg perf” 1

•Check Point Maestro R81.X Getting Started Guide, page 29, section “asg perf” 2

•Check Point Maestro Under the Hood presentation by Lari Luoma, slide 26

1: https://www.manualslib.com/manual/2031661/Check-Point-Maestro-R80-20sp.html 2: https://sc1.checkpoint.com/documents/R81/WebAdminGuides/EN/CP_R81_Maestro_GettingStarted/html_frameset.htm : https://community.checkpoint.com/fyrhh23835/attachments/fyrhh23835/maestro/1191/1/Check%20Mates%20Maestro%20under%20the%20hood%202022.pptx

The RJ-45 connectors located at the front panel of the Orchestrator MHO-170 are used for out-of-band management and serial console access. One of them is a 1Gbps RJ-45 port that provides an out-of-band interface for accessing the Orchestrator itself for configuration and management purposes. The other one is a RJ-45 serial console port that provides a command-line interface for initial setup and troubleshooting.

References

•Maestro Hyperscale Orchestrator Datasheet - Check Point Software1, page 2

•Quantum Maestro Getting Started Guide - Check Point CheckMates, page 4

The Management ports located on the Rear Panel of the Orchestrator MHO-140 are out-of-band interfaces that provide access to the Orchestrator itself for configuration and management purposes. They are not used for traffic distribution or connectivity to the Security Groups or the external networks. They are 1Gbps RJ-45 ports that can be connected to a switch or a router.

References

•Maestro Hyperscale Orchestrator Datasheet - Check Point Software1, page 2

•Quantum Maestro Getting Started Guide - Check Point CheckMates2, page 4

References =

•Check Point Maestro R81.X Administration Guide, page 64, section “Correction Layer” 1

•Check Point Maestro R81.X Getting Started Guide, page 26, section “Correction Layer” 2

•Check Point Maestro Under the Hood presentation by Lari Luoma, slide 23

•Check Point Maestro Frequently Asked Questions (FAQ), question 9

1: https://www.manualslib.com/manual/2031661/Check-Point-Maestro-R80-20sp.html 2: https://sc1.checkpoint.com/documents/R81/WebAdminGuides/EN/CP_R81_Maestro_GettingStarted/html_frameset.htm : https://community.checkpoint.com/fyrhh23835/attachments/fyrhh23835/maestro/1191/1/Check%20Mates%20Maestro%20under%20the%20hood%202022.pptx :https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails= &solutionid=sk147853&partition=Basic&product=Maestro

The Pre-Upgrade Verifier is a tool that checks the compatibility and readiness of the Maestro environment for the upgrade process. It verifies the current version, the target version, the hardware requirements, the configuration settings, and the license validity of the Maestro Orchestrators and the Security Groups. It also identifies any potential issues or risks that might affect the upgrade and provides recommendations on how to resolve them. The Pre-Upgrade Verifier should be run before importing the R81.10 software package and before performing the actual upgrade.

References =

•Check Point R81.10 for Scalable Platforms - Check Point Software

•CHECK POINT MAESTRO EXPERT