EMC Dell RecoverPoint Deploy Achievement D-RP-DY-A-24 Exam Dumps: Updated Questions & Answers (October 2025)

Accessing Installation Manager: Use the boxmgmt user account to log into the Installation Manager. This account has the necessary permissions to make changes to RPA parameters and perform connectivity tests.

Making RPA Parameter Changes: Once logged in, navigate to the RPA settings within the Installation Manager to make any required changes to the RPA parameters.

Testing and Diagnosing Connectivity Issues: The boxmgmt account can also be used to run tests and diagnostics to troubleshoot any connectivity issues that may arise during the deployment or operation of the RecoverPoint system.

For more detailed procedures and best practices, refer to the Dell EMC RecoverPoint documentation, which provides comprehensive guidelines on using the Installation Manager and the boxmgmt user account1.

Check LUN Configuration: The Repository volume must be accessible by all RPAs.If it is configured as a private LUN, it would only be accessible by a single host or a limited set of hosts, which could be why it is not visible in the Deployment Manager1.

Modify LUN Settings: To resolve this, the LUN should be reconfigured to be accessible by all RPAs. This may involve changing the LUN from private to public or shared within the storage array settings.

Verify Visibility: After reconfiguring the LUN, verify that it is now visible in the Deployment Manager to continue with the RecoverPoint cluster configuration.

It is essential that the Repository volume is not set as a private LUN to ensure that all RPAs within the cluster can access it for proper configuration and operation of the RecoverPoint system1.

RecoverPoint offers different configurations depending on the version and setup. For RecoverPoint EX/CL, it supports one production copy and up to six replicated copies.This allows for comprehensive data protection and disaster recovery solutions by maintaining multiple copies of data1.

For detailed information on the capabilities and limitations of the different RecoverPoint versions, please refer to the official Dell EMC RecoverPoint documentation1.

Physical Connection: The RPAs should be physically connected to each other using their iSCSI ports.This is because the host systems are configured with iSCSI HBAs, which indicates that the storage network is based on iSCSI protocol1.

Configuration in RecoverPoint: In the RecoverPoint Deployment Manager, ensure that the iSCSI ports of the RPAs are correctly configured to communicate with the VNX array.

Verification: After the physical connections and configurations are made, verify that the RPAs can communicate with the VNX array and that the iSCSI connections are stable and operational.

It is important to note that while the RPAs are connected through their iSCSI ports, they should not be connected to any MirrorView ports on the VNX array.Additionally, ensure that the RPAs are connected directly to the FC ports on the Storage Processors (SPs) and not to an expansion SFP on the file side1.

Access the CLI: Use the boxmgmt account to log into the Command Line Interface (CLI) of the RecoverPoint Appliance.

Run the Command: Execute the set_user name=admin password= command to initiate the password reset process.

Set New Password: Follow the prompts to set a new password for the admin user.

This process is used when the admin password has been lost and needs to be reset.It is important to follow the correct syntax and procedure to ensure the security and integrity of the system1.

Understanding MetroPoint Consistency Groups: MetroPoint is a configuration that combines VPLEX Metro and RecoverPoint to provide continuous data protection and disaster recovery across multiple sites. A distributed device in this context means that the data is mirrored across two VPLEX clusters.

Fracture Scenario: A fracture between the two VPLEX clusters indicates a disruption in the communication or synchronization between the clusters. This can happen due to network issues, hardware failures, or other disruptions.

Replication Behavior:

Step 1: When a fracture occurs, VPLEX determines a “winner” site based on the configured policies and the state of the clusters.

Step 2: RecoverPoint continues replication through the VPLEX winner site. This means that the replication process will proceed using the site that is still operational and accessible.

Step 3: The losing site will not receive updates until the fracture is resolved. Once the connection is restored, the system will resynchronize the data between the sites.

Verification:

Step 4: Monitor the RecoverPoint Management Application to ensure that replication is continuing through the winner site. Check the status of the Consistency Groups and the health of the replication process.

Step 5: After the fracture is resolved, verify that the data is resynchronized and that both sites are back in sync.

References: This information is verified based on the official Dell RecoverPoint and VPLEX documentation, which outlines the behavior of MetroPoint Consistency Groups and the expected replication behavior during a fracture12.

To re-image a Gen 6 RPA (RecoverPoint Appliance) node, you would typically use a bootable USB memory stick that contains the installation image.

This method is supported because it allows the RPA to boot directly into the installer environment, where you can perform the re-imaging process.

The Dell RecoverPoint for Virtual Machines Installation and Deployment Guide provides instructions on how to install and configure a Dell RecoverPoint system, which includes re-imaging nodes1.

For specific instructions on re-imaging a Gen 6 RPA node, you should refer to the documentation provided with your RPA or available on the Dell EMC support site2.

It’s important to use the correct version of the installation image that matches your RPA model and firmware version to ensure compatibility and a successful re-imaging process.

Please note that while the verified answer is based on general practices for re-imaging devices such as an RPA node, you should always consult the official Dell RecoverPoint documentation or contact Dell EMC support for the most accurate and up-to-date instructions.

Deployment Manager Overview: The Deployment Manager is a tool used to install and configure RecoverPoint clusters. It guides users through various steps to ensure the proper setup and configuration of the system.

Prepare New Cluster for Connection: During this step, the Deployment Manager prepares the new cluster for connection to the existing infrastructure. This involves several sub-steps, including network configuration, validation of the environment, and ensuring that all necessary components are in place.

Adding Licenses: As part of the “Prepare New Cluster for Connection” step, new RecoverPoint licenses are added to the cluster. This is crucial because the licenses enable the functionality of the RecoverPoint system, allowing it to perform replication and recovery tasks.

Verification: After adding the licenses, the Deployment Manager verifies that the licenses are correctly applied and that the cluster is ready for the next steps in the deployment process.

References: This information is verified based on the official Dell RecoverPoint documentation, which outlines the steps and procedures for deploying and configuring RecoverPoint clusters12.

Access the RecoverPoint CLI: The rp_import-certificate command is issued within the RecoverPoint Command Line Interface (CLI).

Purpose of the Command: This command is used to update or import certificates into the RecoverPoint system.It is particularly relevant when certificates have been changed to a self-signed or CA-signed certificate, rather than a default one1.

Execution of the Command: To execute the command, you would typically need to be logged in as a user with appropriate permissions, such as the root or security-admin user.

The rp_import-certificate command is an essential part of maintaining the security of the RecoverPoint system by ensuring that the certificates used for secure communications are up to date1.

Proper communication between Deployment Manager and the RecoverPoint Appliances requires the following ports: TCP 21, 22, 25, 80, and 7225. These ports facilitate the necessary management and data transfer operations essential for the deployment and configuration of RecoverPoint systems.