Huawei HCSP-Field-Data Center Facility V1.0 H20-923_V1.0 Exam Dumps: Updated Questions & Answers (February 2026)

For FusionCol8000-A230, the “two systems” part is correct: Huawei’s quick guide explicitly states that theindoor and outdoor units consist of two independent cooling systems, which is the basis for redundancy and staged capacity control.

However, the rest of the statement (“each system uses three compressors connected in parallel and two EEVs”) is not supported as a fixed, universal configuration in the installation/commissioning guide text that is available here. In Huawei smart cooling designs, compressor quantity and the number of electronic expansion valves (EEVs) aremodel- and configuration-dependentand are tied to how the refrigerant circuit is partitioned (for example, multiple compressor stages for capacity modulation, and one or more EEVs for different evaporator branches). Because the documentation we can directly verify confirmstwo independent systemsbut doesnotconfirm “three compressors per system” as an explicit requirement, the combined statement (two systems + specific compressor/EEV counts) is judgedfalse: one part is verified true, while the detailed component count cannot be confirmed as stated.

In Huawei smart module monitoring architecture, theUIM20A expansion moduleis traditionally used toincrease device portsso cabinets can connect multiple intelligent components and sensors (for example, door status and environmental sensors). Huawei also provides theintelligent rPDU PDU2000M, whosemain control moduleincludes communications and DI interfaces designed to directly接入cabinet-level intelligent devices for centralized monitoring and management. In Huawei’s solution description for rPDU-monitoring networking, thePDU2000M is positioned to replace the expansion-module role, meaning that in applicable scenarios, cabinets can connect monitoring devices through the PDU2000M without deploying an additional UIM20A expansion module. This supports practical connections such asT/H sensors,smart U space managers, anddoor status/door-access related signalsthrough the PDU2000M interfaces, and then these devices are managed/bound in the controller’s smart module view. Huawei O&M guidance also emphasizes avoiding duplicate connections (do not connect the same device to both UIM20A and PDU2000M), aligning with the replacement concept. (Scribd)

Huawei data center facility design typically follows a layered fire protection concept: early detection, controlled alarm linkage, and suppression methods that protect equipment and ensure personnel safety. A smoke detection system (often combined with staged alarms) provides early warning so operators can verify events and initiate emergency procedures. For the IT white space, a clean-agent gas extinguishing system is preferred because it suppresses fire without leaving residue and significantly reduces the risk of corrosion or contamination compared with powder-based agents. The extinguishing system is normally integrated with linkage/interlock controls: audible/visual pre-discharge alarms, time delay, emergency abort, door access control logic, and HVAC shutdown or damper control to help maintain agent concentration. This coordinated mechanism reduces false discharge risk while preserving a reliable automatic response if a real fire develops. In contrast, relying only on manual extinguishers is too slow for rapid fire growth, and water sprinklers alone can cause substantial collateral damage to servers and power equipment.

For FusionCol8000-C chilled-water systems, Huawei commissioning requires awater leakage/pressure-holding teston the chilled-water piping after installation to verify joint sealing, valve interfaces, and connection integrity before long-term operation. The specified method is toraise the water pressure in the chilled-water pipe to 0.8 MPa, then observe for30 minutesto confirm there is no visible leakage. If the system remains dry, the same pressure isretained for 24 hoursas a stability verification step. The acceptance criterion is that thepressure drop is less than 0.01 MPaover the 24-hour period and no leakage is found, which demonstrates that the piping and fittings meet tightness requirements under the prescribed test pressure. This procedure helps prevent future failures such as slow seepage, corrosion around joints, insulation waterlogging, and unexpected shutdowns caused by water loss or low differential pressure alarms. It also ensures that subsequent flushing, venting, and operational commissioning can be performed safely and reliably.

In the FusionDC1000A IT scenario, the power chain is built around an AC input, conditioned backup power, energy storage, and final distribution to the IT racks.Integrated UPSis the core power-conditioning component, providing voltage and frequency stabilization and uninterrupted supply during mains disturbances. The UPS works together withSmartLi, Huawei’s lithium battery system, which serves as the energy storage unit to sustain the load during outages and to support controlled shutdown or generator switchover. After UPS output, power is delivered to the IT loads through thePower PDB, which performs downstream distribution, branch protection, and organized cable termination toward rack PDUs or IT equipment feeders. By contrast, anAC/DC power systemis typically associated with DC bus supply used in telecom-oriented or dedicated DC load scenarios, not the standard IT scenario architecture of FusionDC1000A that is centered on UPS plus battery plus AC distribution. Therefore, the correct components for IT scenarios are SmartLi, Power PDB, and Integrated UPS.

Huawei data center power distribution design prioritizes continuity for critical loads. For single-cord IT equipment that cannot accept dual inputs, an STS provides a practical high-availability approach by connecting the load to two independent AC sources (often A and B feeds) and transferring the load to the healthier source when abnormalities occur. The key value is speed and coordination: the STS detects voltage/frequency deviations or source failure and performs a rapid transfer to minimize or eliminate interruption seen by the load. This supports O&M strategies where upstream systems (UPS, PDUs, distribution boards) are maintained or isolated without forcing downtime on single-cord devices. In routine operations, STS status, transfer logs, alarms, and source quality parameters are monitored to prevent nuisance transfers and to ensure correct upstream selectivity and grounding. Correct commissioning also ensures the two sources meet synchronization conditions and that bypass/maintenance procedures are standardized, improving safety and reducing operational risk.

In Huawei data center facility management,NetEcois the management software platform (server/application) used to centrally monitor and manage sites, whileiBMCis the out-of-band hardware management interface used forserver remote maintenance(such as power control, hardware health, BIOS settings, and remote console) on the specific server where iBMC exists. TheiBMC port is not a service access interface for NetEco. NetEco’s backend services are accessed through theserver operating system network interfaces(management/service network) and corresponding application ports after the server is properly networked and configured. Even if NetEco is deployed on a Huawei server that has iBMC, iBMC only provides a channel to manage the server hardware and does not expose NetEco application access as an official commissioning/O&M path. Therefore, NetEco backend access should be planned via the site’s management network (IP addressing, routing, security policy), not via iBMC.

In Huawei smart module commissioning, the ECC800-Pro controller provides a dedicated management access path through its WAN ports. For on-site startup commissioning, technicians typically connect a laptop directly toWAN1and place the laptop IP address in the same subnet as the controller so they can open the WebUI and complete initial settings (time, network, device discovery, alarm checks, linkage tests, and parameter commissioning). Thefactory default IP address for WAN1 is 192.168.8.10, which is used as the initial access point before the address is planned and changed to match the customer’s management network. This default design supports quick “point-to-point” commissioning without depending on upstream switches, DHCP services, or enterprise IP planning at the very beginning of deployment. After login, Huawei commissioning practice is to harden access (password/authentication completion), then update network parameters and integrate the ECC800-Pro into the site monitoring network to enable continuous O&M, remote alarm reporting, and device management.

In Huawei smart module management (such as on the ECC800-Pro/WebUI),Device Managementis used to centrally view and maintain managed objects (UPS, SmartLi, rPDU, sensors, air conditioners, etc.). TheOverviewpage provides a consolidated snapshot of a device’s operating status, key parameters, running mode, and basic identification information so engineers can quickly judge whether the device is healthy and online. TheAlarmview lists active and historical alarms related to the device, supporting rapid fault isolation and verification after recovery. TheSignalview shows monitoring points and I/O status (including analog values and digital inputs/outputs where applicable), which helps engineers confirm sensor wiring, linkage logic, and real-time state changes during commissioning and troubleshooting. TheService periodinformation is used for lifecycle and maintenance planning, such as tracking service time, maintenance intervals, or component life indicators where supported, enabling preventive maintenance and reducing unexpected downtime. Therefore, Device Management supports viewing all four categories.

In Huawei data center facility equipment (such as precision cooling units and related controllers), alarm presentation follows a clear severity-based design so technicians can recognize urgency immediately without entering detailed menus. Acritical alarmrepresents the highest severity level and is treated as a condition that may impact safe operation, cooling continuity, or equipment protection. For this reason, the LCD controller uses the most prominent visual and audible indications: theindicator turns redto show critical severity, and thebuzzer sounds continuouslyto ensure the alarm cannot be overlooked in a noisy equipment-room environment. This behavior supports rapid response: O&M personnel can quickly identify that immediate action is required, then open the alarm list to locate the root cause, confirm whether the unit has derated or stopped, and execute the prescribed troubleshooting steps (for example, checking power status, sensor readings, fan/compressor status, water flow/pressure, and protection interlocks). Therefore, the statement correctly describes the standard critical-alarm indication method on the LCD controller.