CWNP Certified Wireless Network Administrator CWNA-109 Exam Dumps: Updated Questions & Answers (December 2025)

The channel that can be used for VHT transmissions according to the 802.11 specification is channel 144. VHT stands for Very High Throughput and is the PHY layer specification for 802.11ac devices. VHT transmissions can use channel bandwidths of 20 MHz, 40 MHz, 80 MHz, or 160 MHz in the 5 GHz band. Channel 144 is one of the channels in the 5 GHz band that can support VHT transmissions with any of these bandwidths. Channel 6, channel 1, and channel 11 are channels in the 2.4 GHz band that cannot support VHT transmissions, as they are only compatible with legacy (802.11b/g/n), HT (802.11n), or ERP (802.11g) transmissions with up to 20 MHz bandwidth. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 214; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 204.

DHCP (Dynamic Host Configuration Protocol) is the network service where option 43 must be configured to allow access points to locate controllers. DHCP is a protocol that allows a device to obtain an IP address and other network configuration parameters from a server. In a wireless controller scenario, the access points can use DHCP to request an IP address from a DHCP server, which can also provide the IP address or hostname of the wireless controller as an option in the DHCP response. Option 43 is a vendor-specific option that can be used to encode custom information for different types of devices. For example, Cisco access points can use option 43 to receive the IP address of the wireless controller from the DHCP server, while Aruba access points can use option 43 to receive the hostname of the wireless controller from the DHCP server. This way, the access points can discover the wireless controller and establish a connection with it. References: 1, Chapter 8, page 309; 2, Section 5.2

WLAN bridges must use a channel with acceptable SNR at both transceivers to maintain the desired data rate bi-directionally. A WLAN bridge is a device that connects two or more networks using the 802.11 protocol. A WLAN bridge must have a clear and strong signal between the two endpoints to ensure reliable and fast data transmission. The signal-to-noise ratio (SNR) is a measure of the quality of the signal, which depends on the distance, interference, obstacles, and antenna gain between the transceivers. A higher SNR means a better signal quality and a higher data rate. A lower SNR means a worse signal quality and a lower data rate. Therefore, a WLAN bridge must use a channel with acceptable SNR at both transceivers to maintain the desired data rate bi-directionally1.

 VSWR stands for Voltage Standing Wave Ratio, which is a measure of how well the impedance of the RF cable and connectors matches the impedance of the transmitter and the antenna. Impedance is the opposition to the flow of alternating current in an RF circuit, and it depends on the frequency, resistance, capacitance, and inductance of the components. A perfect impedance match would have a VSWR of 1:1, meaning that all the power is transferred from the transmitter to the antenna, and none is reflected back. However, in reality, there is always some degree of mismatch, which causes some power to be reflected back to the transmitter, creating standing waves along the cable. This reduces the efficiency and performance of the wireless system, and can also damage the transmitter. Excessive VSWR can be caused by using poor quality or damaged cables and connectors, or by using components that have different impedance ratings123. References: CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 90; CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 86; CWNP website, CWNA Certification.

The common spectrum analyzer view that you should use for this analysis is the Waterfall/Spectrogram view. The Waterfall/Spectrogram view shows the signal from the interfering device over time on a three-dimensional graph. The x-axis represents frequency, the y-axis represents time, and the z-axis represents amplitude or power. The color of each pixel indicates the signal strength at a given frequency and time. The Waterfall/Spectrogram view can help you identify the characteristics of the interference source, such as its frequency range, duty cycle, modulation type, and pattern. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 524; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 494.

The HT (802.11n) physical layer (PHY) specification includes support for and compatibility with both ERP and HR/DSSS. ERP stands for Extended Rate PHY, which is an extension of the original DSSS (Direct Sequence Spread Spectrum) PHY that supports data rates up to 54 Mbps in the 2.4 GHz band. HR/DSSS stands for High Rate/Direct Sequence Spread Spectrum, which is another extension of DSSS that supports data rates up to 11 Mbps in the 2.4 GHz band. HT stands for High Throughput, which is a new PHY that supports data rates up to 600 Mbps in both the 2.4 GHz and 5 GHz bands. HT uses OFDM (Orthogonal Frequency Division Multiplexing) as its modulation scheme, but it also supports legacy DSSS and ERP devices by using a dual preamble and header structure that allows backward compatibility. References: , Chapter 3, page 103; , Section 3.1

The unit of measurement that is an absolute unit and is used to quantify received signal power levels on a logarithmic scale is dBm. dBm stands for decibel-milliwatt and represents the power level relative to 1 milliwatt (mW). dBm is an absolute unit because it has a fixed reference point and does not depend on the input power level. dBm is used to measure the received signal power levels on a logarithmic scale because it can express large variations in power levels with small numbers and make calculations easier. For example, a 10 dB increase in power level means a 10-fold increase in power, and a 20 dB increase means a 100-fold increase in power. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 66; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 56.

The response that you should give to your manager’s suggestion of implementing the security practices of disabling the broadcasting of the SSID in Beacons and configuring the access points not to respond to Probe Request frames that have a null SSID field is that any 802.11 protocol analyzer can see the SSID in clear text in frames other than Beacons frames. This negates any security benefit of trying to hide the SSID in Beacons and Probe Response frames. The SSID (Service Set Identifier) is a human-readable name that identifies a WLAN and allows users to connect to it. The SSID is transmitted in clear text in several types of 802.11 frames, such as Beacon frames, Probe Request frames, Probe Response frames, Association Request frames, Association Response frames, Reassociation Request frames, and Reassociation Response frames. Some people may think that hiding the SSID can improve the security of the WLAN by making it invisible to potential intruders. However, this is not true, as hiding the SSID only removes it from Beacon frames and Probe Response frames that have a null SSID field. The SSID is still present in other types of frames that can be easily captured and analyzed by any 802.11 protocol analyzer or wireless scanner tool. Therefore, hiding the SSID does not provide any real security benefit and may even cause some compatibility and performance issues for legitimate users. References: 1, Chapter 4, page 133; 2, Section 4.1

The center frequency of channel 4 in the 2.4 GHz band is 2.427 GHz (2427 MHz). The center frequency of a channel is the midpoint of its frequency range, where the signal strength is highest and most concentrated. The center frequency of channel 1 in the 2.4 GHz band is 2.412 GHz (2412 MHz), as given in the question. The center frequency of each subsequent channel is obtained by adding 5 MHz to the previous channel’s center frequency, since the channels are spaced 5 MHz apart from each other in this band. Therefore, to find the center frequency of channel 4, we need to add 15 MHz (5 MHz x 3) to the center frequency of channel 1:

2.412 GHz + 0.015 GHz = 2.427 GHz

Alternatively, we can use a formula to calculate the center frequency of any channel in the 2.4 GHz band:

Center frequency (GHz) = 2.407 + (0.005 x Channel number)

Using this formula for channel 4, we get:

Center frequency (GHz) = 2.407 + (0.005 x 4)

Center frequency (GHz) = 2.407 + 0.02

Center frequency (GHz) = 2.427 References: 1, Chapter 3, page 85; 2, Section 3.2

 A Wi-Fi scanner is a basic tool that can be used to easily locate areas of high co-channel interference. A Wi-Fi scanner is a software application that can run on a laptop, tablet, smartphone, or other device that has a Wi-Fi adapter. A Wi-Fi scanner can scan the wireless environment and display information about the detected access points and client stations, such as their SSID, BSSID, channel, signal strength, security, and data rate. A Wi-Fi scanner can also show the channel utilization and overlap of different access points, which can indicate the level of co-channel interference. Co-channel interference is a type of interference that occurs when multiple access points use the same or adjacent channels within the same coverage area. Co-channel interference can reduce the throughput and performance of the WLAN, as the access points and client stations have to contend for the channel access and avoid collisions. To identify areas of high co-channel interference, a Wi-Fi scanner can be used to measure the signal strength and channel utilization of different access points and compare them with a threshold or a baseline. Alternatively, a Wi-Fi scanner can also use a color-coded heat map to visualize the co-channel interference level in different locations. References: 1, Chapter 7, page 279; 2, Section 4.3